in
All Tags » router (RSS)

Browse by Tags

  • SSH breaks after changing hostname in Cisco IOS router

    I changed the hostname on my Cisco router and now it stopped accepting SSH connections. I have already deleted and regenerated my RSA key. Fortunately, I still have console access. Code Snippet: 1: 2: 3: 4: 5: 6: 7: 8: 9: 10: 11: 12: 13: 14: 15: 16: 17: 18: 19: 20: 21: 22: 23: 24: 25: 26: 27: 28: 29...
    Posted to Routers (Forum) by hardware on 03-11-2010

  • Cisco 2811, cannot enable WIC module

    Hello, I'm having an issue with a WIC card (HWIC-1DSU-T1). There is another card (VWIC2-2MFT-T1/E1) in the system and it works just fine. Here the relevant output: uptime is 7 hours, 37 minutes System returned to ROM by power-on System image file is "flash:c2800nm-ipbase-mz.124-3i.bin"...
    Posted to Routers (Forum) by hardware on 03-09-2010

  • Cisco 800 Router what is Port 10000?

    I have a Cisco 800 router on the network that acts as gateway/isp router. When I run a nmap scan to the cisco IP address NMAP returns Interesting ports on 192.168.10.1: 10000/tcp open snet-sensor-mgmt? Can someone tell me why this port is open and what is the function of this service?
    Posted to Routers (Forum) by hardware on 03-02-2010

  • policy-based routing with cisco 1811

    Hi I'm working on a cisco 1811/k8 with 2x fe ports and 8 built-in ports. the diagram will explain more than my word. fe0 has public IP 64.62xxxx. Our DNS point domain.com to this IP. vlan1 has 2 load-balanced web servers and being NAT'd to fe0. fe1 has public IP 65.49xxxx. Our DNS point sub1...
    Posted to Routers (Forum) by hardware on 03-02-2010

  • Cisco 1841 wont route between connected subnets?

    I have a brand new 1841 ISR. I have plugged it in, and plugged one cable into one of our subnets' swtiches (FE0/1 192.168.43.0) and one cable into the other subnets' switches (FE0/0 10.10.10.0) My config is below. Here is what i get from a "show ip route": Gateway of last resort is...
    Posted to Routers (Forum) by hardware on 03-01-2010

  • How do I limit incredibly short bursts of traffic with Cisco 2821 router?

    We have a problem with one of our WAN links where the provider has provisioned us with a 20mbit circuit, which we generally stay under, however when our backups start pulling data from the remote site, the provider starts dropping packets as we are bursting above 20mbit (even though our 5-minute average...
    Posted to Routers (Forum) by hardware on 02-26-2010

  • Juniper router default password

    Can anyone tell me the default password for J2320 Juniper router? I believe it has Junos9.1
    Posted to Routers (Forum) by hardware on 02-25-2010

  • Cisco Dual NAT for Failover links

    It seems simple enough. I have a really complicated (sarcasm) T1 with 5 static IP addresses. I've had this T1 for years, so i know my configuration is correct... or it was until now. I recently was offered a DSL backup.... NOT for the servers, but for the desktop users. The boss thinks that the servers...
    Posted to Routers (Forum) by hardware on 02-24-2010

  • Forward more than 10 ports?

    The Linksys routers that i have will only alow me to forward a max of 10 ports. Is there a way to fake that out i need to have 14 ports forwarded. Or does anybody know of a cheep router that will alow me to port forward more than 10 ports. I would like it to have a HTML interface.
    Posted to Routers (Forum) by hardware on 02-22-2010

  • How to connect two CISCO 2811 series router

    I am new to CISCO routers. In one of our site I have to connect 2 CISCO 2811 series routers. Both of them are used for normal LAN purpose (No WAN). The following are the builit in interfaces in these routers 2 100 base T 2 USB ports 1 console ports 1 Auxillary ports One 2811 series is configured for...
    Posted to Routers (Forum) by hardware on 02-21-2010
Page 1 of 72 (718 items) 1 2 3 4 5 Next > ... Last ยป